MMC-16 APC to 8 x LC UPC Harness CableMMC-16 APC to 8 x LC UPC Harness Cable, 16 Fibers, OM4
New Zealand engineering teams can use the documented values below to compare the product with the intended channel and as-built requirements. This OM4 MMC-to-LC harness fans one MMC-16 APC female connector out to eight LC UPC duplex legs. Sixteen bend-insensitive multimode fibers provide eight duplex optical routes for switches, servers or patch panels. While factory-finished LC branches eliminate the need for an individual multimode cassette, the single 2.5mm plenum trunk keeps the central channel compact.
Product Highlights
- MMC Female to LC UPC Duplex, 16 Fibers
- OM4 50/125μm, bend-insensitive fiber
- MMC insertion loss ≤0.35dB, return loss ≥40dB
- LC insertion loss ≤0.2dB, return loss ≥30dB
- Harness Polarity wiring scheme
- 2.5mm Plenum (OFNP) cable
- Standard length options: 1m (3ft), 2m (7ft), 3m (10ft)
Specifications
| Part Number | 16FMMCLCOM4 |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MMC Female (Non-Pinned) |
| Connector B | LC UPC Duplex |
| Polish Type | APC to UPC |
| Glass Fiber | Bend Insensitive Fiber |
| Fiber Mode | OM4 50/125μm |
| Wavelength | 850/1300nm |
| Fiber Count | 16 Fibers |
| Polarity | Harness Polarity |
| Cable Outside Diameter (OD) | 2.5mm |
| Cable Jacket | Plenum (OFNP) |
| Min. Bend Radius (Optical Fiber) | 7.5mm |
| Min. Bend Radius (Fiber Cable) | 20/10D (Dynamic/Static) |
| Tensile Strength (Long Term) | 30N |
| Tensile Strength (Short Term) | 100N |
| MMC Connector IL | ≤0.35dB |
| MMC Connector RL | ≥40dB |
| LC Connector IL | ≤0.2dB |
| LC Connector RL | ≥30dB |
| Attenuation at 850nm | ≤2.3dB/km |
| Attenuation at 1300nm | ≤0.6dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Direct fan-out for multimode equipment
The relevant harness is suitable when a MMC-based parallel interface must connect to LC duplex hardware using OM4. It does not on its own perform electronic conversion or change lane speeds; it provides the passive fiber assignment only. Cross-check that the active port expects this breakout arrangement and that each LC leg is assigned to the compatible duplex destination.
MMC and LC optical values
Maximum insertion loss is 0.35dB at MMC and 0.2dB at LC. Minimum return loss is 40dB for the MMC APC interface and 30dB for LC UPC. OM4 attenuation is 2.3dB/km at 850nm and 0.6dB/km at 1300nm. Use these figures with the transceiver budget and other connections to review every full duplex optical path.
Managing eight LC duplex branches
Define regular length versions of 1m (3ft), 2m (7ft) or 3m (10ft), or specify project-specific meter and foot lengths. Eight branch pairs need orderly routing to prevent crossed transmit and receive connections. Label the legs before bundling, support the relevant fan-out body and maintain the 7.5mm minimum fiber bend radius near the connection interfaces.
Ordering and Factory Support
Reference 16FMMCLCOM4 with the intended length and quantity. Submit your preferred LC branch identifiers and MMC label data; the factory may align these markings with the rack’s duplex-port numbering to simplify future moves and fault isolation. New Zealand project orders can include documentation and labeling requirements alongside the technical configuration.
