AFBR-734ASMZBrocade AFBR-734ASMZ Compatible 25G SFP28 SR Transceiver Module
Built for hosts recognizing AFBR-734ASMZ, this HT-manufactured SFP28 module delivers 25G transmission at 850nm. Its rated reach is 100m on OM4 / 70m on OM3, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: AFBR-734ASMZHT Part Number: SFP-25GSR-85-I
Product Highlights
- Compatible alternative to Brocade AFBR-734ASMZ
- 25G connectivity at 25.78Gbps
- Optical wavelength: 850nm
- Specified reach: 100m on OM4 / 70m on OM3
- Duplex LC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| Brocade Compatible | AFBR-734ASMZ |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-25GSR-85-I |
| Form Factor | SFP28 |
| Max Data Rate | 25.78Gbps |
| Wavelength | 850nm |
| Max Cable Distance | 100m@OM4/70m@OM3 |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -7.9~1.9dBm |
| Receiver Sensitivity | ＜-6dBm |
| Power Budget | -1.9dB |
| Receiver Overload | 2.4dBm |
| Power Consumption | ＜1W |
| Extinction Ratio | ＞2dB |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| CDR | TX & RX Built-in CDR |
| FEC Function | Support RS-FEC, FC-FEC |
| Protocols | IEEE 802.3by, SFF-8472, SFF-8432, SFP28 MSA, CPRI, eCPRI |
| Core Size | 50/125 µm |
| Packaging Technology | COB Packaging |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 100m on OM4 / 70m on OM3 figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Brocade Compatibility and Factory Testing
The module is checked for host recognition as AFBR-734ASMZ, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.9~1.9dBm; receiver sensitivity is ＜-6dBm; the stated optical power budget is -1.9dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 25.78Gbps, wavelength 850nm, rated reach 100m on OM4 / 70m on OM3.
Ordering Information
Quote HT part number SFP-25GSR-85-I together with OEM reference AFBR-734ASMZ and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies AFBR-734ASMZ, not an original Brocade-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 100m on OM4 / 70m on OM3, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
