Customized MPO-8 to 2 x MPO-4 BreakoutCustomized MPO-8 to 2 x MPO-4 Breakout Cable, 8F, Type B, OM4
A MPO Female breakout cable for parallel to parallel or parallel to duplex connections. 8 Fibers, OM4 50/125μm, Plenum (OFNP)/Dual Rated (OFNR/LSZH). Each leg is labeled and length matched in the factory for a clean installation.
Available lengths are 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft) and 30m (98ft). We can also produce any intermediate or longer length to order, with your choice of labeling and packaging.
Product Highlights
- MPO Female (Non-Pinned) to MPO Female (Non-Pinned), 8 Fibers
- OM4 50/125μm, bend insensitive fiber
- Insertion loss ≤0.35dB, return loss ≥45dB
- Type B polarity
- 3.0mm Plenum (OFNP)/Dual Rated (OFNR/LSZH) round cable
- Minimum bend radius 7.5mm
- Stock lengths from 1m (3ft) to 30m (98ft), custom lengths on request
Specifications
| Part Number | 8FMPOOM4 |
|---|---|
| Manufacturer | HT |
| Connector A | MPO Female (Non-Pinned) |
| Connector B | MPO Female (Non-Pinned) |
| Fiber Mode | OM4 50/125μm |
| Wavelength | 850/1300nm |
| Polish Type | APC to APC |
| Polarity | Type B |
| Cable Jacket | Plenum (OFNP)/Dual Rated (OFNR/LSZH) |
| Fiber Count | 8 Fibers |
| Glass Fiber | Bend Insensitive Fiber |
| Minimum Bend Radius | 7.5mm |
| Cable Outside Diameter (OD) | 3.0mm |
| Trunk Length | 0.2m |
| Installation Tensile Load | 66N |
| Tensile Strength | 60/120N (Long/Short Term) |
| 400G Ethernet Distance | 50/100m at 850nm |
| 800G Ethernet Distance | 50m at 850nm |
| Insertion Loss | ≤0.35dB |
| Return Loss | ≥45dB |
| Attenuation at 850nm | ≤2.3dB/km |
| Attenuation at 1300nm | ≤0.6dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Applications
In leaf-spine and GPU cluster cabling, this breakout replaces a cassette plus multiple jumpers with one tested assembly. The 8-fiber version matches 400G and 800G parallel interfaces that run on 4 or 8 lanes, such as QSFP112, OSFP and twin-port OSFP connections. Each leg is marked so port mapping is unambiguous during installation.
Breakout Geometry and Wiring
Each breakout leg is individually jacketed, labeled and measured, and the transition from trunk to legs is protected against pulling forces. If your installation needs different leg lengths or a different lane mapping, we can build it to your drawing.
Ordering Information
Ordering is simple: send us 8FMPOOM4 and your required lengths and quantities, and we return a factory quote the same working day. Small trial orders are welcome before you commit to a full project rollout.
Quality and Testing
Every MPO/MTP assembly leaving our factory is 100% tested for insertion loss and return loss, with end face geometry checks on the multi-fiber ferrules. Controlled polishing keeps the loss budget stable across the whole batch, which matters when several mated pairs sit in one link.
Built to Your Spec
Our engineering team handles custom MPO/MTP assemblies daily. If the standard configuration does not match your link design, send us the requirement and we will build exactly what your network needs at factory-direct cost.
How We Pack
Each assembly is coiled, capped and sealed in an individual bag, then packed into foam lined export cartons. Test reports can be attached per unit or per batch, and carton marks follow your shipping instructions.
