10/100BASE-T SFPIntel E10GSFPSRX Compatible 10G SFP+ SR Transceiver Module 300m on OM3 / 400m on OM4
The E10GSFPSRX compatible module serves equipment requiring a 10G SFP+ interface with 850nm optics and a 300m on OM3 / 400m on OM4 rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: E10GSFPSRXHT Part Number: SFP-10GSR-85
Product Highlights
- Compatible alternative to Intel E10GSFPSRX
- 10G connectivity at 10.3125Gbps
- Optical wavelength: 850nm
- Specified reach: 300m on OM3 / 400m on OM4
- Duplex LC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Intel Compatible | E10GSFPSRX |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GSR-85 |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Wavelength | 850nm |
| Max. Transmission Distance | 300m@OM3/400m@OM4 |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -7.3~-1dBm |
| Receiver Sensitivity | < -11.1dBm |
| Power Budget | 3.8dB |
| Receiver Overload | -1dBm |
| Max. Power Consumption | ≤1W |
| Extinction Ratio | >3dB |
| DDM/DOM | Supported |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Core Size | 50/125µm |
| Modulation | NRZ |
| BER | 1E-12 |
| MTBF | 11,300,000 Hours @40°C, 90%CL |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 300m on OM3 / 400m on OM4 figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Intel Compatibility and Factory Testing
The module is checked for host recognition as E10GSFPSRX, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.3~-1dBm; receiver sensitivity is < -11.1dBm; the stated optical power budget is 3.8dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10.3125Gbps, wavelength 850nm, rated reach 300m on OM3 / 400m on OM4.
Ordering Information
When ordering, specify E10GSFPSRX, SFP-10GSR-85, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each E10GSFPSRX compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Intel transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies E10GSFPSRX, not an original Intel-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 300m on OM3 / 400m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
