SFP+ to SFP+-10G-AOC-1M3FTSFP+ to SFP+-10G-AOC-1M3FT 10G SFP+ Industrial Active Optical Cable, 1m (3ft)
The SFP+ to SFP+-10G-AOC-1M3FT compatible cable combines 10G AOC connectivity with a defined 1m (3ft) pathway between SFP+ to SFP+ interfaces. It is intended for Generic equipment and is documented here as a distinct order code, allowing cable schedules, service access and related length selections to be reviewed before installation.
OEM Part Number: SFP+ to SFP+-10G-AOC-1M3FTHT Part Number: SFP+ to SFP+-10G-AOC-1M3FT
Product Highlights
- HT-manufactured AOC assembly in 1m (3ft)
- Interface configuration: SFP+ to SFP+
- Fixed length and part number: 1m (3ft), SFP+ to SFP+-10G-AOC-1M3FT
- Minimum bend radius: 30mm
Specifications
| HT Part Number | SFP+ to SFP+-10G-AOC-1M3FT |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP+ to SFP+ |
| Max Supply Voltage | 3.45 V |
| Minimum Bend Radius | 30mm |
| Cable Length | 1~300m@OM3 MMF |
| Wavelength | 850nm |
| Built-in CDR | NO |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Modulation | NRZ |
| Bit Error Rate | 1E-12 |
| Jacket Material | OFNP |
| Built-in FEC | NO |
| Protocols | SFF-8431,10GBASE Ethernet, Fibre Channel |
| Operation temperature | -40 to 85°C (-40 to 185°F) |
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Position Within the Length Range
SFP+ to SFP+-10G-AOC-1M3FT is the shortest of 3 verified length options in this family. It is the preferred choice when the port positions are close and cable slack must be kept to a minimum. The next option is SFP+ to SFP+-10G-AOC-50M164FT at 50m (164ft), adding 49m for a less direct routing path; selecting it unnecessarily would leave more cable to dress.
Structured Pathways and Serviceability
Treat the direct-attach assembly as part of the permanent pathway plan even when the link is expected to be temporary. Follow the intended horizontal and vertical managers, maintain the specified bend radius and leave service access around both ports. A small, supported service allowance is preferable to excess slack concealed inside a rack or placed under cable-tie pressure. For this assembly, the minimum bend radius is 30mm; the jacket material is OFNP.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFF-8431,10GBASE Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
At 1m (3ft), SFP+ to SFP+-10G-AOC-1M3FT is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.
Ordering Information
Include the part number, fixed length, quantity and required pathway or rack grouping in the order information. The host model and firmware release are useful for change-controlled deployments. Different lengths should remain separate order lines so delivered labels and packing records agree with the pathway plan. Quantity and any labeling instructions should be attached specifically to SFP+ to SFP+-10G-AOC-1M3FT.
Generic Compatibility and Factory Testing
Verification covers the physical connectors, expected host identity and an operating link with available diagnostic indications. We distinguish this complete check from a simple continuity test. Platform model and software release can be reviewed in advance where the installation has strict documentation or change-control requirements. The check includes receive activity and diagnostic indications, followed by a final inspection of both ends.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. International express, air cargo and sea freight can be selected according to destination and carton volume; customer courier accounts and nominated forwarders are also accepted.
Quality Assurance and Packaging
After connector inspection and link verification, the assembly is coiled without tight bends and packed with end protection. Labels can cross-reference the customer cable schedule, OEM part number and length. This supports both receiving checks and later moves, adds or changes. Volume orders can include customer references on the labels and carton list.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Does this order code cover multiple lengths?
No. SFP+ to SFP+-10G-AOC-1M3FT refers here to 1m (3ft). Every other verified length has a separate part number and page in the length list.
